Datasheets MeanWell

CONSTANT CURRENT REGION Note.4 SPECIFICATION MODEL DC VOLTAGE OUTPUT CURRENT ADJ. RANGE LINE REGULATION LOAD REGULATION SETUP, RISE TIME Note.6 HOLD UP TIME (Typ.) VOLTAGE RANGE Note.5 FREQUENCY RANGE POWER FACTOR (Typ.) AC CURRENT (Typ.) INPUT INRUSH CURRENT(Typ.) LEAKAGE CURRENT MAX. NO. of PSUs on 16A CIRCUIT BREAKER SAFETY STANDARDS WORKING TEMP. WORKING HUMIDITY MAX. CASE TEMP. STORAGE TEMP., HUMIDITY VIBRATION MTBF DIMENSION OTHERS OVER CURRENT OVER VOLTAGE OVER TEMPERATURE 47 ~ 63Hz PF 0.98/115VAC, PF 0.97/230VAC, PF 0.95/277VAC @ full load ≧ ≧ ≧ 5A / 115VAC 2.45A / 230VAC 2A / 277VAC <0.75mA / 277VAC 2unit(circuit breaker of type B) / 3units(circuit breaker of type C) at 230VAC 95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed Compliance to EN55015,EN61000-3-2 Class C (@ load 50%) ; EN61000-3-3; GB17743, GB17625.1 ≧ Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, light industry level (surge immunity Line-Earth 4KV, Line-Line 2KV) 20 ~ 95% RH non-condensing Tcase= +90 ℃ -40 ~ +80 , 10 ~ 95% RH ℃ non-condensing 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes 345.5K hrs min. Telcordia SR-332(Bellcore) ; 95.3K hrs min. MIL-HDBK-217F (25 ) ℃ 262*125*43.8mm (L*W*H) VOLTAGE TOLERANCE Note.3 ENVIRONMENT SAFETY & EMC PROTECTION SHORT CIRCUIT Constant current limiting, recovers automatically after fault condition is removed 94% 94.5% 94.5% 95% 95% 95.5% 95% 95.5% 94.5% 95% 95% 95% ± 1.0% ± 1.0% ± 1.0% ± 1.0% ± 1.0% ± 1.0% 10 ~ 20A 8 ~ 16A 6.6 ~ 13.3A 5.7 ~ 11.4A 5 ~ 10A 4.4 ~ 8.9A ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% 24V HLG-480H-24 HLG-480H-30 HLG-480H-36 HLG-480H-42 HLG-480H-48 HLG-480H-54 30V 36V 42V 48V 54V 12 ~ 24V 15 ~ 30V 18 ~ 36V 21 ~ 42V 24 ~ 48V 27 ~ 54V EMC IMMUNITY EMC EMISSION COLD START 35A(t =1800 s measured at 50% I ) at 230VAC; Per NEMA 410 width peak TOTAL HARMONIC DISTORTION 480W Constant Voltage + Constant Current LED Driver HLG - 480H se r i e s File Name:HLG-480H-SPEC 2016-12-01 THD< 20% (@ load 40% / 115VAC,230VAC,277VAC) ≧ (Please refer to TOTAL HARMONIC DISTORTION (THD) section) " " I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH ℃ 16ms 115VAC/230VAC 500ms, 80ms 115VAC/230VAC 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) Tcase= -40 ~ +90 ℃ (Please refer to "OUTPUT LOAD vs TEMPERATURE" section) Shut down output voltage, re-power on to recovery Shut down output voltage, re-power on to recovery RATED CURRENT RATED POWER VOLTAGE ADJ. RANGE RIPPLE & NOISE (max.) Note.2 20A 16A 13.3A 11.4A 10A 8.9A 480W 480W 478.8W 478.8W 480W 480.6W 200mVp-p 200mVp-p 250mVp-p 250mVp-p 250mVp-p 350mVp-p Adjustable for A-Type only (via built-in potentiometer) Adjustable for A-Type only (via built-in potentiometer) 20.4 ~ 25.2V 25.5 ~ 31.5V 30.6 ~ 37.8V 35.7 ~ 44.1V 40.8 ~ 50.4V 45.9 ~ 56.7V 27 ~ 33V 33 ~ 40V 40 ~ 50V 46 ~ 55V 53 ~ 63V 60 ~ 70V (Please refer to " " ) POWER FACTOR (PF) CHARACTERISTIC section ISOLATION RESISTANCE WITHSTAND VOLTAGE UL8750(type”HL”), CSA C22.2 No. 250.13-12; ENEC EN61347-1, EN61347-2-13 independent, EN62384; GB19510.14,GB19510.1; IP65 or IP67 approved TEMP. COEFFICIENT ± ℃ ℃ 0.02%/ (0 ~ 60 ) PACKING 2.8Kg;4pcs/12.2Kg/0.58CUFT NOTE 5< ' ! ;H8 9 ! ! '( 6 + !3 ! < ℃ < I ! D"@ + 3 , 39 5 J % ! , <5 + I 0 + < < 8 1 6 < < / + J) . .;$ D*8"H) H #*) DH)K#*J< < ) ! 9 3 < / < % + > 8'8.( ("' '(8* . 8.(? + < # , + ! ! + < 8 H; H , ! 9 + , ! < 0< 8, ! , 3 !3 , + E ! < *D( + ! 3 ++ 39 , ! 6 , + E ! ! + ! %E +9 *D( ) , ! < < 8 + + E ! + , * / + , + 7 6 , #*) 9 3 3 , , , ! 9 , ! < =< 8, ! , 9 + 7 9 + : 6 , + , 8 6 9 8D/6 )#( 6 3 0 < ℃ 5 < / + , 9 ! D*'; &*##G 3 , 1 <! < ! μ EFFICIENCY (Typ.) 230VAC 277VAC